Showing results: 106 - 120 of 1308 items found.
-
Kyoritsu Electrical Instruments Works, Ltd.
The insulation resistance (IR) test (also commonly known as a Megger) is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance in either k, M or G.
-
1863 -
IET Labs
The GenRad 1863 Megohmmeter is the choice for production and inspection tests on devices with resistances up to 20 Tohms. The GenRad 1863 will measure resistance at any of five test voltages of: 50V, 100V, 200V, 250V, and 500 VDC. Compared to the GenRad 1864, which has adjustable test voltages from 10V to 1090V, this unit has fewer controls, and is the more economical of the two models.
-
Torontech Group
Test Chambers are used widely in temperature variation tests, cold resistance tests, and for low-temperature storage in the areas of aerospace and aviation, electronic instruments, electrical products, materials, parts, and components.
-
RMO-M Series -
IBEKO Power AB
The motor/generator winding resistance test is used to identify open windings, shorts between two windings, short to grounds, connection mistakes or shorted turns. This non-invasive test of winding resistance helps to pinpoint problems regarding windings in stator or rotor part of an electrical machine. Additionally, motor winding ohmmeter has the capability of performing heat run test which will show a change in windings resistance with an increase of temperature.The RMO-M series is designed as an ideal aid in preventive maintenance of electrical motors and generators. They are powerful (up to 100A of test current), portable (8 kg) and generate DC current which is completely ripple-free. This makes measurement very precise with 0,1% accuracy.Three voltage channels make measurement very easy since it is possible to obtain a value of all three winding resistances in one measurement
-
SCR ELEKTRONIKS
Dry Arc Resistance Tester is designed to conduct high voltage,low current Arc Resistance test on solid electrical insulation material as per:ASTM standard D495-99 (2004) and UL 746A. Why Arc Resistance Test? Many Cases of insulator failure are due to deterioration of its surface because of sustained electrical discharge or Arc. This test method is intended to test the resistance of insulating material when a high -Voltage low -current Arc close to the surface of insulation, intending to form a conducting path therein or in causing the material to become conducting due to decomposition and erosion.AdvantagesThis Test ensures that your products meet high standards of quality & safety. This product is meant for all Switchgears/ insulator/ Polymer/ electro plastic manufacturers and manufacturers who use insulators in their products e.g. Wiring Accessories, Appliances, HT/LT line insulators etc.
-
UI-FT37 -
Unuo Instruments
Maeser Water Penetration Tester is used to test footwear upper leather dynamic water resistance. It is suitable for all kinds of shoe upper leather. Water penetration and water absorption can be measure by Maeser water resistance tester.
-
METRISO 3000 -
Wolfgang Warmbier GmbH & Co. KG
Suitable for resistance point-to-point and resistance to ground measurementsIntegrated data logger with USB communication port for data transmission (50.000 test values). The supplied Report Generating Software ETC allows to generate a complete test reportHumidity and temperature sensorA barcode scanner can be used in order to record measurement points before testing
-
Megger Group Ltd.
Cable testing can be broken down to different steps of the process, starting with a time domain reflectometer test to look for an incident signal on the line or, in some high resistance situations, VLF testing. These tests will identify a fault, allowing you to move on to pre-locating it. In some low resistance faults this will occur alongside the identification via the TDR.
-
Vogelsang & Benning
Series test rig for starter-generator units (ISG)*High voltage test*Insulation resistance measurement*Temperature sensor control*Short circuit test*EMF test*Performance measurement*Manual loading and contacting
-
Dongguan Amade Instruments Technology Co., Ltd
Packaging testing equipment are intended to measure the resistance of corrugated containers to various crushes and burst at given conditions, applied to bursting strength test, ring crush test, edge crush test, flat crush test, pin adhesion test, puncture strength test, bending stiffness test, corrugating medium test, compression test, damp-proof test etc. As corrugated boxes assume the important responsibility of loading and protecting goods playing an inevitable role in modern logistics, so the properties of corrugated boards have to be mastered by manufacturers and users prior to use. The physical performances which are measured by a series of testings are core factors for judging the quality of packaging boxes. Paper testing items mainly include quantification, thickness measurement, whiteness, smoothness,breaking elongation, burst resistance, folding resistance, stiffness, tearability, degree of sizing, etc.
-
PMK-153 -
Prostat Corporation
The PMK-153 Resistance Test Kit contains the instruments you need to take resistance measurements.The PMK-153 includes the PAS-853B Wide Range Ohmmeter with 5 pound Conductive Rubber Electrodes. The PAS-853B instrument is a wide range ohmmeter that measures accurately from 0.01 to 9.9x1012 ohms. In AUTO mode the instrument automatically adjusts resistance range and selects test voltage in accordance with standard practices outlined in ANSI/ESD STM11.11, and meets audit requirements of ESD TR53.
-
SKZ148 -
SKZ Industrial Co., Ltd
Dart impact testing machine used for plastic films and sheets of impact test to evaluate the impact resistance, it adopts background light source for test results.
-
TG070 -
TESTEX Testing Equipment Systems Ltd.
Geotextile Hydrostatic Pressure Tester, to determine the property of penetration resistance of geotextiles by static hydraulic pressure test.
-
-
UI-FT45 -
Unuo Instruments
Akron Abrasion Tester is used to test rubber abrasion resistance and it is suitable for rubbers with a hardsness in the range of 55-85IRHDx.